Peacehaven High Driveway Gate from

Choose your options
Need advice? Give us a call
0800 6124 965 / 0330 6600 107

Peacehaven Wrought Iron Driveway/ Entrance Gates:

Manufactured by hand in the UK by skilled craftsmen using the finest materials to provide ultimate durability and quality. All of our gates come complete with a
10 year workmanship guarantee, adjustable hinges, latch, 2 x drop bolts. With this design, specifications of the frame will change according to width. For widths under 10ft, 25mm x 10mm frame will be used. For gates of 10ft and over, we use a 25mm x 25mm frame.

Width of Gate: Taken as if both sides were touching each other. For example, a width from the drop down menu of 10ft (3m 048mm) would be 2 x 5ft wide. If you are measuring a gap between existing posts/ pillars, we recommend reducing the opening size by 6" (150mm) to allow for hinge/ pins and centre clearance.

Height of Gate: Taken to the highest point of each gate. We recommend allowing a 50mm (2") clearance between the bottom edge of gate and driveway (as long as the drive is level). If you require a more exact height, please contact us to order.

Gate Furniture Included (hinges etc): 4 x adjustable hinges, hinge pins, latch and drop bolts included with each gate. As standard, the position of the hinge will be 6" (150mm) from the bottom edge of gate and 6" (150mm) from top edge of gate. If you require these to be different (if for example you already have pins set into a post/ pillar), please call us.

Metal Hanging Gate Posts:  Our posts come with a feature pyramid post cap and the hanging pins pre welded so once the posts are fitted the gates can be easily hung onto the pins. The finish of them is the same as the finish you choose for your gate. We correctly match the height of your post for you to suit your gate. Choose between wall fitted posts (requires bolts to fix to your wall and the post holes drilled on site)  or below ground which can be concreted in.

We recommend: 
2 x 80mm x 80mm for opening under 8ft wide
2 x 100mm x 100mm for opening width 8ft and over
2 x 120mm x 120mm for opening width 10ft and over (if your gate is under 4ft tall then a 100mm x 100mm will be suitable)

Supplied to allow the posts to sit in the ground to a depth of 1ft 5" (450mm). The post will arrive cut to size (therefore, if you selected a gate height of 3ft 6", the post length will be 4ft 11") unless above ground post is chosen. 
Size of Gate not listed? No problem, call us with your exact size.

Why choose us

Hand crafted gates individually made here in the UK

Can be made to ANY width and height

We construct gates to a very high standard, using the correct size metal for each gate depending on the style and size. This gives you a very strong gate which will last for many years

Adjustable hinges, 2 x drop bolts and ring latch are included with your gate

10 Year workmanship guarantee against welds

One of UK's largest gate manufacturers approved by Trading Standards

Delivered straight to your door

  • Working out the required size is an important yet simple task to complete but we are always at hand to assist you through the process (0800 6124 965)

    Calculating Driveway Gate width between existing Pillars or Posts:

    Take three measurements, top, middle and bottom (as below).

    How to measure for driveway gate

    Take the shortest of the three measurements and reduce by 150mm (or 6"). This allows for the hinge (inc pins) and centre opening gap. The final figure will be the actual width of gate required.

    For example: Top: 3m 455mm | Middle: 3m 450mm | Bottom: 3m 445mm - shortest measurement would be 3m 445mm - reduce by 150mm = Actual Gate Width of: 3m 295mm

    Download PDF Measurement Guide


As standard, the frame size and bar diameter are used as below. If preferred, we can increase the frame size (or add box frame etc) on request. To do so, please call us.
Gate width under 10ftGate width 10ft and over
Hanging Style25mm x 10mm25mm x 25mm
Bottom Rail25mm x 10mm25mm x 25mm
Top, Middle and Closing Rail25mm x 10mm25mm x 25mm
Main Infill Bars12mm Diameter12mm Diameter
Scrolls12mm x 3mm12mm x 3mm
Hanging Style 25mm x 10mm (or over 10ft) 25mm x 25mm
Bottom Rail 25mm x 10mm (or over 10ft) 25mm x 25mm
Top and Middle Rail 25mm x 10mm (or over 10ft) 25mm x 25mm
Closing Rail 25mm x 10mm
Main Infill Bars 12mm
Handcrafted in the UK Bespoke, any width or height
Guarantee 10 year against gate welds
Opening Electric or manual